↓

1941 Studebaker Champion

Living with an old Studebaker

1941 Studebaker Champion
Home→Categories Repair and Upgrades - Page 2 << 1 2 3 4 >>

Category Archives: Repair and Upgrades

Post navigation

← Older posts
Newer posts →

Oil leak hunt

Posted on June 4, 2023 by nvonadaJune 4, 2023
3

When I was working on the manifold leaks I noticed that there is an oil leak down by the oil pump. It is not streaming out, but the engine pan is wet and there was oil on the bottom of … Continue reading →

Posted in Repair and Upgrades | Tagged Oil leak | 3 Replies

Re-installed the manifold

Posted on April 29, 2023 by nvonadaApril 29, 2023
Reply

Got the manifold back yesterday from M & M Head Service. They resurfaced the mating surface and it is nice and flat now. I am lucky to have a good machine shop in the area but they are super busy … Continue reading →

Posted in Repair and Upgrades | Tagged Manifold | Leave a reply

Attempt #2 at the valve adjustment

Posted on April 16, 2023 by nvonadaApril 16, 2023
Reply

The engine has not sounded right since I adjusted the valves. I already found one exhaust leak, which helped, but it still sounds wrong. Time to bite the bullet and figure out what is wrong. … Continue reading →

Posted in Repair and Upgrades | Tagged Manifold, Valve adustment | Leave a reply

Passenger side door latch

Posted on April 2, 2023 by nvonadaApril 2, 2023
Reply

I was taking my neighbor for a ride and the door did not want to latch. The problem was not hard to find. … Continue reading →

Posted in Repair and Upgrades | Leave a reply

Found my exhaust leak

Posted on February 26, 2023 by nvonadaFebruary 26, 2023
Reply

Since I did the valve adjustment the car has sounded like it has an exhaust leak. I thought it was the manifold gasket. But I was only 1/2 right. After driving the car for a while I spotted this: Besides … Continue reading →

Posted in Repair and Upgrades | Tagged Engine | Leave a reply

Finished up turn signals

Posted on February 26, 2023 by nvonadaFebruary 26, 2023
Reply

I wanted to do a better job routing the wires for the new front turn signals. This is what I came up with. These are essentially the same as the clips Studebaker used to attach the wiring harness to the … Continue reading →

Posted in Repair and Upgrades | Tagged Wiring | Leave a reply

Front turn signals

Posted on February 5, 2023 by nvonadaFebruary 5, 2023
Reply

My plan back when I did the wiring last year was to put a set of Unity vintage fog lights on the car for front turn signals. But I waited too long and Unity discontinued their vintage line. They make … Continue reading →

Posted in Repair and Upgrades | Tagged bumper, chrome, Wiring | Leave a reply

Troubleshooting a turn signal indicator

Posted on January 21, 2023 by nvonadaJanuary 21, 2023
2

Back when I did the new wiring harness I said that everything was working perfectly. It turns out that was not correct. I did not realize at the time that the new turn signal switch had a light in the … Continue reading →

Posted in Repair and Upgrades | Tagged Wiring | 2 Replies

Replaced the fuel line

Posted on July 30, 2022 by nvonadaJuly 30, 2022
Reply

There has not been a lot of Studebaker work this summer because I have been working on this: We build a new 40’x26′ shop with a BendPak lift. It is going to rock but has sucked up all of my … Continue reading →

Posted in Repair and Upgrades | Leave a reply

Headlights are out

Posted on September 13, 2020 by nvonadaSeptember 13, 2020
1

Friday night Maria and I took the Stude into town.  We left at dusk and when I turned the headlights on nothing happened except the instrument lights got really dim.  Parking and taillights work fine.  So today I started tracking … Continue reading →

Posted in Repair and Upgrades | Tagged Wiring | 1 Reply

Post navigation

← Older posts
Newer posts →
© 2025 - 1941 Studebaker Champion
↑